Trufast Roofing Adhesive is a construction-grade, polyurethane foam adhesives designed to adhere to approved roof insulations, thermal barriers, cover boards and fleece backed membranes to acceptable substrates.

Features and Benefits:

Clean, odorless, fast one-step application resulting in significant labor savings for the contractor

Ready to use, no mixing (tanks require shaking)

VOC, CFC, HCFC and solvent free

Full cure within minutes

No compressed or melted insulation

Cartridges and tanks do not require an expensive specialty pump/spray rig, drums are for pump cart

Remains flexible, absorbs stress

No external power source necessary for minimal noise disruption (cartridges and tanks)

Superior wind-uplift resistance

Eliminates thermal bridging

No building height restrictions

Packaged in a self-contained disposable can or canister, TILE BOND™ is a portable one-component polyurethane foam roof tile adhesive for attaching concrete and clay roof tiles. It is quicker and easier to install compared to traditional attachment methods such as screws, mortar, wire ties and clips. Minimal expanding TILE BOND™ also provides greater attachment strength while minimizing nail penetrations and reducing roof weight loads. With its easyto-use dispensing equipment, TILE BOND™ can be quickly and efficiently dispensed in a highly consistent manner, eliminating the need for expensive equipment and ratio monitoring.

FROTH-PAK™ Foam Insulation is a twocomponent, quick-cure polyurethane foam that fills cavities, penetrations, cracks and expansion joints. Unlike one-component foam, FROTH-PAK™ Foam Insulation is a chemically cured foam, significantly reducing curing time. FROTH-PAK™ Foam Insulation dispenses, expands and becomes tack-free in seconds.

The product will skin over in 30–40 seconds and will be completely cured in minutes. The Class-A rating (flame spread of 25 or less) of FROTH-PAK™ Foam Insulation allows its use in a wide range of interior and exterior industrial, commercial, institutional and residential settings. Check with local codes prior to use. If used in an exterior setting, a coating must be applied for ultraviolet (UV) protection.

INSTA STIK™ Quik Set Commercial Roofing Adhesive is a single component polyurethane adhesive dispensed from a portable disposable pre-pressurized container requiring no external power source.

The #12 DP Roofing Fasteners are specifically engineered to secure insulation, coverboards, and base sheets to corrugated steel (16-22 gauge) and wood substrates. Featuring a #2 double flute self-drilling point and exclusive tapered entry thread design, they penetrate steel quickly and offer exceptional back-out resistance.

The #12 Purlin Fastener is a self-drilling fastener engineered to secure single-ply roofing membrane to structural steel purlins (16 ga. to 3/16”) in standing seam metal roof recover applications. The specially designed ¾” long pilot point prevents the existing metal roof panel from “jacking” up the threads during the drilling operation, thereby reducing point burnout and breakage.

The #14 HD Fastener is engineered to secure insulation, coverboards, base sheets and single-ply roof membrane systems to corrugated steel (16 - 22 ga.), wood, and concrete substrates. Featuring a #2 double flute self-drilling point and exclusive tapered entry thread design, they penetrate steel quickly and offer exceptional back-out resistance.

The #14 HD Stainless Steel Bi-Metal Roofing Fastener is made of 316 austenitic stainless steel alloy with a hardened carbon steel drill point. This all purpose roofing fastener is engineered to secure insulation, coverboards, base sheets and single-ply roof membrane systems to corrugated steel (18-24 ga.) and wood substrates. The #2 double flute self-drilling point and excludisve tapered entry thread design penetrates steel quickly.

The #15 EHD Fastener is engineered for lap attachment to corrugated steel (18 – 22 ga.) and wood substrates in higher wind uplift roof assemblies. Featuring a #2 double flute self-drilling point and exclusivetapered entry thread design, they penetrate steel quickly and offer exceptional back-out resistance.

The Concrete Spike Fastener is a one-piece, vibration-resistant anchor designed to fasten insulation, single-ply roof membrane, wood, and steel to structural concrete roof decks. Featuring an “S” shaped configuration at the working end of the fastener to create an expansion mechanism, it provides a fast, reliable fastening solution for structural concrete roof applications.

TRUFAST® originated the combination of the pre-assembled fastener and insulation plate to increase the productivity of attaching insulation to metal and wood roof decks. Together with the specially designed stand-up tools and accessories for fastener placement and attachment, TRUFAST offers a simple, economical, and ergonomic “system solution” to increase productivity in the mechanical attachment of roof insulation. TRUFAST Pre-assembled fasteners and plates feature a #12 drill point fastener with a 3” Galvalume™ plate and are available in #3 Phillips Truss Head (PA) and ¼” Hex Head (PAH) styles. The combination of a durable canvas fastener bag and a lightweight, adjustable magnetic setter tool allows a roofer to quickly and accurately place fasteners in the desired fastening pattern without bending over. The setter tool will install fasteners into most roofing materials, including gypsum cover boards. The lightweight and easy to maneuver TRUFAST 0-2500 rpm Stand-Up Power Tool allows the operator to quickly and comfortably drive the fasteners to the proper depth without special training.

An Electric 2500 RPM screw gun used in unison with the pre-assembled fastener tip to quickly install TRUFAST pre-assembled fasteners.

TRUFAST® originated the combination of the pre-assembled fastener and insulation plate to increase the productivity of attaching insulation to metal and wood roof decks. Together with the specially designed stand-up tools and accessories for fastener placement and attachment, TRUFAST offers a simple, economical, and ergonomic “system solution” to increase productivity in the mechanical attachment of roof insulation. TRUFAST Pre-assembled fasteners and plates feature a #12 drill point fastener with a 3” Galvalume™ plate and are available in #3 Phillips Truss Head (PA) and ¼” Hex Head (PAH) styles. The combination of a durable canvas fastener bag and a lightweight, adjustable magnetic setter tool allows a roofer to quickly and accurately place fasteners in the desired fastening pattern without bending over. The setter tool will install fasteners into most roofing materials, including gypsum cover boards. The lightweight and easy to maneuver TRUFAST 0-2500 rpm Stand-Up Power Tool allows the operator to quickly and comfortably drive the fasteners to the proper depth without special training.

TRUFAST® originated the combination of the pre-assembled fastener and insulation plate to increase the productivity of attaching insulation to metal and wood roof decks. Together with the specially designed stand-up tools and accessories for fastener placement and attachment, TRUFAST offers a simple, economical, and ergonomic “system solution” to increase productivity in the mechanical attachment of roof insulation. TRUFAST Pre-assembled fasteners and plates feature a #12 drill point fastener with a 3” Galvalume™ plate and are available in #3 Phillips Truss Head (PA) and ¼” Hex Head (PAH) styles. The combination of a durable canvas fastener bag and a lightweight, adjustable magnetic setter tool allows a roofer to quickly and accurately place fasteners in the desired fastening pattern without bending over. The setter tool will install fasteners into most roofing materials, including gypsum cover boards. The lightweight and easy to maneuver TRUFAST 0-2500 rpm Stand-Up Power Tool allows the operator to quickly and comfortably drive the fasteners to the proper depth without special training.

TRUFAST® VERSA-FAST® Metal Plates are used to mechanically attach insulation, cover boards and base sheets to light weight insulating concrete and gypsum decks. The Versa-Fast Metal Plate is a circular design with one center fastener placement hole and eight equally spaced fastener placement holes around the perimeter of the plate allowing for maximum versatility. Required pullout values can be achieved by installing multiple Versa-Fast Fasteners in one Versa-Fast Metal Plate. Patent No. 10,190,616

For base sheet, recovery board, and insulation attachment to lightweight insulating concrete, structural woodfiber, and poured gypsum. Formed from coated steel to prevent corrosion, the twin loc-nail easily penetrates decking and existing membranes.

TRUFAST® Metal Insulation Plates are used to mechanically attach insulation, coverboards and BUR base sheets to the substrate. The plate’s circular design and reinforcing ribs provide exceptional strength to resist wind uplift forces.

TRUFAST 2” TL Seam Plate is used to attach reinforced single-ply and modified bituminous membranes to cementitious wood fiber, gypsum and lightweight concrete substrates. Use with TRUFAST TL Roofing Fastener.

TRUFAST® VERSA-FAST® FASTENERS are engineered to secure insulation, coverboard and base sheets to light weight insulating concrete and gypsum decks. The Versa-Fast Fastener features an exclusive thread design engineered for exceptional pull out resistance. When used in conjunction with the VERSA-FAST® Metal Plate, multiple fasteners can be installed to achieve the required minimum pull out. Patent No. 10,190,616

TL Fastener is designed to mechanically attach rigid insulation board and single-ply membrane to structural cement wood fiber, gypsum and lightweight insulating concrete roof decks. It features a high thread profile with a tapered root diameter and sharp point. Its unique design allows it to penetrate the roof deck and progressively compact the base material, creating a stronger hold in weak material. The TL Fastener is used in conjunction with the TRUFAST 2” TL Seam Plate and 3” TL Insulation Plate.

For Base Sheet attachment to lightweight insulating concrete and various gypsum roofdecks

For Base Sheet Attachment to higher density lightweight insulating concrete, NVS concrete and various gypsum roofdecks.

For Wood and Timber Application. Featuring a large, pancake head style with a 6-lobe drive, TRUFAST SIP Fasteners drive quickly and smoothly, and draw panels securely without the need of a washer.

For Light Duty corrugated steel deck and wood applications. Featuring a large, pancake head style with a 6-lobe drive, TRUFAST SIP Fasteners drive quickly and smoothly, and draw panels securely without the need of a washer.

For Heavy Duty thick steel applications. Featuring a large, pancake head style with a 6-lobe drive, TRUFAST SIP Fasteners drive quickly and smoothly, and draw panels securely without the need of a washer.

The TRUFAST® Induction Weld (IW) Plates are designed to attach insulation or coverboards to the deck while providing a non-penetrating mechanical attachment of single-ply membranes utilizing an induction welded bond to the TRUFAST IW Plate. Plates are available for use with TPO or PVC/KEE/TPA membranes. TRUFAST IW Plates are approximately 3-3/8" (85.4 mm) diameter. Plates are approved for use with steel, wood or structural concrete roof decks.

TRUFAST® Metal Insulation Plates are used to mechanically attach insulation, coverboards and BUR base sheets to the substrate. The plate’s circular design and reinforcing ribs provide exceptional strength to resist wind uplift forces. TRUFAST Metal Insulation Plates are made of Galvalume coated steel for excellent corrosion protection that meet the requirements of ASTM D6294, FM 4470 and DIN 50018. TRUFAST 3" Recessed Metal Insulation Plate has a deep center recess to accommodate hex headed fasteners and prevent screw heads from snagging mops and penetrating into membrane. It is used to attach roof insulation to the substrate and should only be used over compressible insulations.

TRUFAST® Metal Insulation Plates are used to mechanically attach insulation, coverboards and BUR base sheets to the substrate. The plate’s circular design and reinforcing ribs provide exceptional strength to resist wind uplift forces. TRUFAST Metal Insulation Plates are made of Galvalume coated steel for excellent corrosion protection that meet the requirements fo ASTM D 6294, FM 4470 and DIN 50018. TRUFAST 3” Metal Insulation Plate has a flat bottom and is used to attach roof coverboards, insulation, and BUR base sheets to the substrate.

TRUFAST 2.4" Scoop Seam Plates are used to attach reinforced single-ply & modified bituminous membranes to the substrate

TRUFAST 2.4” Metal Seam Plates are used to attach reinforced single-ply and modified bituminous membranes to the substrate. Use with Trufast #14HD, #14 Stainless Steel HD, #15EHD, Purlin, Fluted Concrete Nail or 1/4” Concrete Spike fasteners.

TRUFAST 2.4” Metal Seam Plates are used to attach reinforced single-ply and modified bituminous membranes to the substrate. Use with Trufast #14HD, #14 Stainless Steel HD, #15EHD, Purlin, Fluted Concrete Nail or 1/4” Concrete Spike fasteners.

TRUFAST 2” Barbed Metal Seam Plate is used to attach reinforced singly-ply and modified bituminous membranes to the substrate. Use with Trufast #14HD, #14 Stainless Steel HD, #15 EHD, Purlin, Fluted Concrete Nail or 1/4” Concrete Spike fasteners.

Trufast Roofing Adhesive is a construction-grade, polyurethane foam adhesives designed to adhere to approved roof insulations, thermal barriers, cover boards and fleece backed membranes to acceptable substrates.

Features and Benefits:

Clean, odorless, fast one-step application resulting in significant labor savings for the contractor

Ready to use, no mixing (tanks require shaking)

VOC, CFC, HCFC and solvent free

Full cure within minutes

No compressed or melted insulation

Cartridges and tanks do not require an expensive specialty pump/spray rig, drums are for pump cart

Remains flexible, absorbs stress

No external power source necessary for minimal noise disruption (cartridges and tanks)

Superior wind-uplift resistance

Eliminates thermal bridging

No building height restrictions

Trufast Roofing Adhesive is a construction-grade, polyurethane foam adhesives designed to adhere to approved roof insulations, thermal barriers, cover boards and fleece backed membranes to acceptable substrates.

Features and Benefits:

Clean, odorless, fast one-step application resulting in significant labor savings for the contractor

Ready to use, no mixing (tanks require shaking)

VOC, CFC, HCFC and solvent free

Full cure within minutes

No compressed or melted insulation

Cartridges and tanks do not require an expensive specialty pump/spray rig, drums are for pump cart

Remains flexible, absorbs stress

No external power source necessary for minimal noise disruption (cartridges and tanks)

Superior wind-uplift resistance

Eliminates thermal bridging

No building height restrictions

Trufast Roofing Adhesive is a construction-grade, polyurethane foam adhesives designed to adhere to approved roof insulations, thermal barriers, cover boards and fleece backed membranes to acceptable substrates.

Features and Benefits:

Clean, odorless, fast one-step application resulting in significant labor savings for the contractor

Ready to use, no mixing (tanks require shaking)

VOC, CFC, HCFC and solvent free

Full cure within minutes

No compressed or melted insulation

Cartridges and tanks do not require an expensive specialty pump/spray rig, drums are for pump cart

Remains flexible, absorbs stress

No external power source necessary for minimal noise disruption (cartridges and tanks)

Superior wind-uplift resistance

Eliminates thermal bridging

No building height restrictions

Trufast Roofing Adhesive is a construction-grade, polyurethane foam adhesives designed to adhere to approved roof insulations, thermal barriers, cover boards and fleece backed membranes to acceptable substrates.

Features and Benefits:

Clean, odorless, fast one-step application resulting in significant labor savings for the contractor

Ready to use, no mixing (tanks require shaking)

VOC, CFC, HCFC and solvent free

Full cure within minutes

No compressed or melted insulation

Cartridges and tanks do not require an expensive specialty pump/spray rig, drums are for pump cart

Remains flexible, absorbs stress

No external power source necessary for minimal noise disruption (cartridges and tanks)

Superior wind-uplift resistance

Eliminates thermal bridging

No building height restrictions